Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
Are you currently in search of ideas concerning Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately hard project. If the old bathtub is conveniently available, the task can move rapidly; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub as well as embeded in the brand-new one. Ensure you have actually certified yourself for the task and also fit attempting it. Instead of working with a contractor to take over a halfway-completed task, it is far better to consider utilizing one prior to you start. Chances are you may require a specialist plumber to make tube links.
This article will assist you mount a brand-new bathtub in your restroom if you have actually currently acquired a new tub and don't require to change the plan of your previous water system pipelines.
Your tools and material checklist ought to make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin making sure that the washers remain in area between the faucet and also the sink. Protect the tap in position with the manufacturer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind should be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of the two wooden boards under its feet, put the bathtub in the needed position. The wood boards are useful in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the supply of water as well as examine all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub needs to wait till the bathtub has actually been used at least when as this will certainly settle it into its final setting.
Preparing for the Installment
To start with, the sustaining framework supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last placement.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to crack a rigid seal, creating the water to pass through the wall between the bathroom and also the tiling, causing problems with dampness and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can break fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily offered on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that page on A Step-by-Step Guide to Installing a Bathtub while doing a search on the search engines. Sharing is nice. Helping others is fun. Thank you for your time. Visit us again soon.
Book A Free Estimate Report this page